China

    Fuel Cell Standards

 


Identification GB/T 20042.1-2005
    Proton Exchange Membrane Fuel Cell Terminology

 

Scope Various types of proton exchange membrane fuel cells.
Status Published. Available from www.standards.net.cn/ 

Under revision as 20130691-T-604. Scheduled for completion in the middle of 2016.


Identification GB/T 20042.2-2008
    Proton Exchange Membrane Fuel Cell - Part 2: General technical specification of fuel cell stacks

 

Scope Basic requirements for safety and performance of PEM fuel cell stacks. Requirements of type tests, routine tests, acceptance test programs, test methods as well as markings and instructions.

Status Published. Available from www.standards.net.cn/

Identification GB/T 20042.3-2009
    Proton Exchange Membrane Fuel Cell – Part 3: Test method for proton exchange membrane

Scope Various types of proton exchange membrane.  Terminology and definitions of proton exchange membrane test methods for PEM fuel cells.  Thickness uniformity test, proton conductivity test, ion exchange equivalent test, permeability test, tensile test, swelling test and water absorption rate test.

Status Published. Available from www.standards.net.cn/

Identification GB/T 20042.4-2009
    Proton Exchange Membrane Fuel Cell
–Part 4: Test method for electrocatalysts

 

Scope Terminology and definitions of electrocatalyst test methods for PEM fuel cells. Platinum content of the test, the electrochemical activity of the test area, surface area, pore volume, pore size distribution test, morphology and size distribution test, the crystal structure test, the catalyst bulk density and single cell polarization curve test.

Status Published. Available from www.standards.net.cn/

Identification GB/T 20042.5-2009
    Proton Exchange Membrane Fuel Cell
– Part 5: Test method for membrane electrode assembly

 

Scope Terminology and definitions of MEA test methods for PEM fuel cells. Thickness uniformity test, Pt loading capacity test, single cell polarization curves, hydrogen permeation current density test, the activation over potential and ohmic polarization over potential polarization test, electrochemical active surface area test.    

Status Published. Available from www.standards.net.cn/

Identification GB/T 20042.6-2011
   
Proton Exchange Membrane Fuel Cell – Part 6: Test method of bipolar plate properties

 

Scope

This part specifies test procedures of materials of bipolar plate, such as, gas tightness, density, flexural strength and resistance, corrosion current density and components of bipolar plate, such as, gas tightness, resistant drop, area utilization, thickness uniformity, flatness, mass and resistance.

 

This standard applies to polymer electrolyte fuel cell.

Status Published. Available from www.standards.net.cn/

Identification

GB/T 20042.7-2014
   
Proton exchange membrane fuel cells  Part 7: Test methods of carbon paper properties

 

Scope

This part of GB/T 20042 provides test methods foe PEMFC carbon paper properties.

 

Test items include thickness uniformity, resistance, mechanical strength, gas permeability, porosity, bulk density, area density, surface roughness.

 

Status Published. Available at www.standards.net.cn/

Identification GB/Z 21742-2008
    Portable Proton Exchange Membrane Fuel Cell Power Systems

 

Scope For a.c. and d.c. type portable fuel cell systems (not for road vehicles).  The following fuels and fuel feedstocks are within the scope of this standard: 1) hydrogen, 2) natural gas, 3) liquefied petroleum, such as, propane and butane, 4) liquid alcohols such as methanol and ethanol, 5) gasoline, 6) diesel, 7)kerosene, 8) metals, such as Zn or Al, or 9) chemical hydrides.

Status Published. Available from www.standards.net.cn/

Identification GB/Z 21743-2008
    Stationary Proton Exchange Membrane Fuel Cell Power System – Test Methods for Performance

 

Scope Adopted part of IEC 62282 series that covers operational and environmental aspects of the stationary fuel cell power systems performance.  The test methods apply as follows:

     a.  power output under specified operating and transient conditions,
     b.  electrical and thermal efficiency under specified operating conditions
     c.  environmental characteristics; e.g. gas emissions, noise, etc. under specified operating and transient conditions.


Coverage for electromagnetic compatibility is not provided.

Status Published. Available from www.standards.net.cn/

Identification GB/T 23645-2009
    Test methods of fuel cell power system for passenger cars

 

Scope Terminology and definitions, accuracy of the test instrumentation, preparation for test, test condition and performance test methods of fuel cell power system for passenger cars.

Status Published. Available from www.standards.net.cn/

Identification GB/T 23646-2009
    Fuel cell power system for electric bicycles – Technical specification

 

Scope Terminology and definitions, technical parameters, technical requirements, test methods, inspection rules, requirements of markings and instructions.

Status Published. Available from www.standards.net.cn/

Identification GB/T 23751.1-2009
    Micro Fuel Cell Power System – Part 1: Safety

 

Scope This consumer safety standard, adapter from IEC 62282 series, covers micro fuel cell power systems, micro fuel cell power units and fuel cartridges that are wearable or easily carried by hand, providing d.c. outputs that do not exceed 60 V d.c. and power outputs that do not exceed 240 VA. Portable fuel cell power systems that provide output levels that exceed these electrical limits are covered by IEC 62282-5-1.

Adaptation of IEC 62282-6-100: 2007.

Status Published. Available from www.standards.net.cn/

Identification GB/T 23751.2-2009
    Micro Fuel Cell Power System – Part 2: Performance test methods

 

Scope Adapter from IEC 62282 series, provides test methods which are required for the performance evaluation of micro fuel cell power systems for laptop computers, mobile phones, personal digital assistants (PDAs), cordless home appliances, TV broadcast cameras, autonomous robots, etc. This standard describes the performance test methods for power characteristics, fuel consumption and mechanical durability for micro fuel cell power systems with output up to 60 V d.c. and 240 VA.

Adaptation of IEC 62282-6-200: 2007.

Status Published. Available from www.standards.net.cn/

Identification GB/Z 23751.3 - 2013
    Micro fuel cell power system – Part 3: Fuel cartridge interchangeability

 

Scope Adaptation of IEC 62282-6-300: 2009 without any change

Adaptation of IEC 62282-6-300: 2009.
Status

Published 2013. Available at www.standards.net.cn/


Identification

GB/T 25319-2010

    Fuel cell test system used for motor vehicles – Technical specification

 

Scope

This standard specifies terms and symbols, requirement, test method, verification rules and test report of polymer electrolyte fuel cell power system for motor vehicles.

 

This standard applies to polymer electrolyte fuel cell power system for motor vehicles.

Status Published.  Available at www.standards.net.cn/

Identification GB/T 25447-2010
    Proton exchange membrane fuel cell test system and activation system

 

Scope

This standard specifies condition for use, requirement for safety, requirement for technology, test method and verification rules of proton exchange membrane fuel cell test system and activation system.

 

This standard is applies to Proton exchange membrane fuel cell test system and activation system. Useable fuels including hydrogen, reformed gas, liquid alcohol (e.g. methanol), and useable oxidants including air and oxygen and so on.

 

Status Published.  Available at www.standards.net.cn/

Identification GB/T 27748.1-2011
   
Stationary fuel cell power system – Part 1: Safety

 

Scope Adaptation of international standard, IEC 62282-3-1:2007 .
Status Published. Available from www.standards.net.cn/

A new project has been approved (20130683-T-604) to update this document to the 2012 edition of IEC 62282-3-100. The completion date is scheduled for the end of 2016.


Identification GB/T 27748.2-2013
    Stationary fuel cell power system – Performance test methods

 

Scope Adaptation of IEC 62282-3-200:2011 without any change
Status

Published 2013. Available at www.standards.net.cn/


Identification GB/T 27748.3-2011
     Stationary fuel cell power system – Part 3:  Installation
Scope Adaptation of international standard, IEC 62282-3- 3:2007
Status Published. Available from www.standards.net.cn/

Identification GB/Z 27753-2011
     Test Method for Adaptability to Operating Conditions of Membrane Electrode Assembly Used in PEM Fuel
     Cells
Scope

This technical document is specifies terms and definitions, boundary conditions, environmental conditions for test, test  preparation and test report.

 

This technical document applies to membrane electrode which is corresponding to performance requirements proposed by  testing organization. Active area of the testing single electrode is 5 cm Χ5 cm. The corresponding relations between acceleration test and real life is not in consideration.

Status Published. Available from www.standards.net.cn/

Identification GB/T 28183-2011
     Test methods of fuel cell power system for bus
Scope

This standard provides technical requirement, test items of fuel cell power system, test procedures and methods.

 

Test items in this standard including: tightness, start-up at room temperature, performance, insulating properties and mass.

 

This standard is applies to Proton exchange membrane fuel cell system for bus.

Status Published. Available from www.standards.net.cn/

Identification

GB/T 28816-2012

    Fuel Cells – Terminology
Scope Adaptation of international standard, IEC/TS 62282-1:2010.
Status Published 2012. Available from www.standards.net/cn/

Identification

GB/T 28817-2012

    Single cell test methods for polymer electrolyte fuel cells (PEFC)
Scope Adaptation of international standard, IEC 62282-7-1:2010.
Status Published 2012. Available from www.standards.net/cn/

Identification GB/T 29838 - 2013
    Fuel cell Modules

 

Scope Adaptation of IEC 62282-2:2012.  The only change is in Chapter 5 (Type test). adding dielectric test (Static) after 5.9 Dielectric strength test.
Status Published 2013. Available at www.standards.net.cn/

Identification GB/T 30084 - 2013
    Portable fuel cell power system – Safety

 

Scope Adaptation of IEC 62282-5-1:2012 without any change
Status

Published 2013. Available at www.standards.net.cn/


Identification GB/T 31035-2014
    Test methods for proton exchange membrane fuel cell stack at subzero environment

 

Scope

This standard provides general safety requirement, test condition, measurement instrument, routine test before subzero test and test methods at subzero condition including test report.

 

This standard applies to the test of proton membrane fuel cell  stack storage, start, performance at subzero condition.

 

Status Published. Available at www.standards.net.cn/

Identification

GB/T 31036-2014
     Proton exchange membrane fuel cell backup power system: Safety

 

Scope

This standard provides definition and terminology, safety requirement, type test, marking, labeling and packaging related to proton exchange membrane fuel cell system for backup power supply.

 

This standard applies to proton exchange membrane fuel cell  backup power systems:

·         Provide AC or DC output

·         Using hydrogen and air as reactants

 

This standard does not cover safety requirements for location of installation.

Status Published. Available at www.standards.net.cn/

Identification

GB/T 31037.1-2014

    Fuel cell power system used for industrial lift truck applications   Part 1: Safety

 

Scope

This standard provides safety requirements and protection against hazards of fuel cell used for industry truck application.

 

This standard applies to proton exchange membrane fuel cell using hydrogen gas as fuel and air as oxidant, does not cover the part of energy storage.
Status Published. Available at www.standards.net.cn/

Identification

GB/T 31037.2-2014
    Fuel cell power system used for industrial lift truck applications   Part 2: Technical specification

 

Scope

This standard provides technical requirement, test methods, assessment criteria and technical report of fuel cell used for industry truck application.

 

This standard applies to proton exchange membrane fuel cell using hydrogen gas as fuel and air as oxidant, does not cover the part of energy storage.

 

Status Published. Available at www.standards.net.cn/

Identification

GB/T 31886.1-2015
    Test method about the influence of gaseous contami
nant in air on performance of proton exchange membrane fuel cells
- Part 1: Gaseous contaminant(s) in air

 

Scope

This standard provides single cell performance test method for proton exchange membrane fuel cell before and after using SO2, NOX  as contaminant in air.

 

This standard applies to the concentration of contaminant not less than 1 ΅ L/L

 

Status Published. Available at www.standards.net.cn/

Identification

GB/T 31886.2-2015
   
Test method about the influence of gaseous contaminant in the fuel hydrogen on the performance of proton exchange membrane fuel cells - Part 2: Gaseous contaminant(s) in hydrogen

 

Scope

This standard provides single cell performance test method for proton exchange fuel cell before and after using CO as contaminant in hydrogen.

 

This standard applies to the concentration of contaminant not less than 1 ΅ L/L

 

Status Published. Available at www.standards.net.cn/

Identification

Plan No. 20130682-T-604
   
Proton exchange membrane fuel cell module for road vehicle

 

Scope  
Status Scheduled for completion by March 2017.

Identification

Plan No. 20130683-T-604
   
Stationary Fuel Cell Power Systems - Safety

 

Scope Adaption of IEC 62282-3-200:2012, with revisions.
Status Scheduled for completion by March 2017.

Identification

Plan No. 20130684-T-604
    Stationary fuel cell power system – Part 3: Installation

 

Scope Adaption of IEC 62282-3-200:2012, revised.
Status Scheduled for completion by March 2017.

Identification

Plan No. 20130686-T-604
   
Micro fuel cell power systems – Performance test methods

 

Scope Adaption of IEC 62282-6-200:2012, with revisions.
Status

Scheduled for completion by March 2017.


Identification

Plan No. 20130687-T-604
     
Micro fuel cell power systems – Safety – General requirements 

 

Scope Adaption of IEC 62282-6-101
Status Scheduled for completion by November 2018.

Identification

Plan No. 20130688-T-604
   
Stationary fuel cell power system – Performance test methods for small fuel cell power systems

Scope Adaption of IEC 62282-3-201:2013.
Status Scheduled for completion by March 2017.

Identification

Plan No. 20130689-T-604
   
Direct methanol fuel cell system  Part 1: Safety

Scope  
Status Scheduled for completion by March 2017.

Identification

Plan No. 20130690-T-604
   
Direct methanol fuel cell system  Part 2: Performance test method

 

Scope  
Status Scheduled for completion by March 2017.

Identification

Plan No. 20130691-T-604
   
Proton exchange membrane fuel cell  Part 1: Terminology

Scope Revision of GB/T 20042.1-2005
Status Scheduled for completion by March 2017.

Identification

Plan No. 20130692-T-604
   
Test method for proton exchange membrane fuel cell power system at subzero environment

 

Scope  
Status

Scheduled for completion by March 2017.


Identification

Plan No. 20132465-T-604
   
Single cell/stack performance test methods for solid oxide fuel cells (SOFC)

 

Scope Adaption of IEC 62282-7-2:2014.
Status

Scheduled for completion by November 2017.


Identification

Plan No. 20141665-T-604
    Technical Requirement on Fuel Cell Hydrogen Supply

 

Scope  
Status

Scheduled for completion by March 2018.


Identification

Plan No. 20151724-T-604
    Power Supply of Hydrogen Fuel Call for Power System

 

Scope  
Status

Scheduled for completion by November 2018.